1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
|
/*************************************************************************
* Testing sketch for Freematics OBD-II UART Adapter
* Reads and prints several OBD-II PIDs value and MEMS sensor data
* Distributed under GPL v2.0
* Visit http://freematics.com for more information
* Written by Stanley Huang <support@freematics.com.au>
*************************************************************************/
#include <SoftwareSerial.h>
#include <OBD2UART.h>
// On Arduino Leonardo, Micro, MEGA or DUE, hardware serial can be used for output
// as OBD-II UART adapter uses to Serial1
// On Arduino UNO and those have no Serial1, we use software serial for output
// as OBD-II UART adapter uses to Serial
SoftwareSerial mySerial(A2, A3);
//#define mySerial Serial
COBD obd;
void testOut()
{
static const char cmds[][6] = {"ATZ\r", "ATL1\r", "ATH0\r", "ATRV\r", "0100\r", "010C\r", "0902\r"};
char buf[128];
for (byte i = 0; i < sizeof(cmds) / sizeof(cmds[0]); i++) {
const char *cmd = cmds[i];
mySerial.print("Sending ");
mySerial.println(cmd);
if (obd.sendCommand(cmd, buf, sizeof(buf))) {
char *p = strstr(buf, cmd);
if (p)
p += strlen(cmd);
else
p = buf;
while (*p == '\r') p++;
while (*p) {
mySerial.write(*p);
if (*p == '\r' && *(p + 1) != '\r')
mySerial.write('\n');
p++;
}
} else {
mySerial.println("Timeout");
}
delay(1000);
}
mySerial.println();
}
void readPIDSingle()
{
int value;
mySerial.print('[');
mySerial.print(millis());
mySerial.print(']');
mySerial.print("RPM=");
if (obd.readPID(PID_RPM, value)) {
mySerial.print(value);
}
mySerial.println();
}
void readPIDMultiple()
{
const byte pids[] = {PID_ENGINE_LOAD, PID_COOLANT_TEMP, PID_RPM, PID_SPEED, PID_TIMING_ADVANCE, PID_INTAKE_TEMP, PID_THROTTLE, PID_FUEL_LEVEL};
int values[sizeof(pids)];
if (obd.readPID(pids, sizeof(pids), values) == sizeof(pids)) {
mySerial.print('[');
mySerial.print(millis());
mySerial.print(']');
for (byte i = 0; i < sizeof(pids) ; i++) {
mySerial.print((int)pids[i] | 0x100, HEX);
mySerial.print('=');
mySerial.print(values[i]);
mySerial.print(' ');
}
mySerial.println();
}
}
void readBatteryVoltage()
{
mySerial.print('[');
mySerial.print(millis());
mySerial.print(']');
mySerial.print("Battery:");
mySerial.print(obd.getVoltage(), 1);
mySerial.println('V');
}
void readMEMS()
{
int acc[3];
int gyro[3];
int temp;
if (!obd.memsRead(acc, gyro, 0, &temp)) return;
mySerial.print('[');
mySerial.print(millis());
mySerial.print(']');
mySerial.print("ACC:");
mySerial.print(acc[0]);
mySerial.print('/');
mySerial.print(acc[1]);
mySerial.print('/');
mySerial.print(acc[2]);
mySerial.print(" GYRO:");
mySerial.print(gyro[0]);
mySerial.print('/');
mySerial.print(gyro[1]);
mySerial.print('/');
mySerial.print(gyro[2]);
mySerial.print(" TEMP:");
mySerial.print((float)temp / 10, 1);
mySerial.println("C");
}
void setup()
{
mySerial.begin(115200);
while (!mySerial);
// this will begin serial
obd.begin();
mySerial.print("Adapter version: ");
mySerial.println(obd.version);
delay(1000);
// send some commands for testing and show response for debugging purpose
//testOut();
Serial.print("MEMS:");
if (obd.memsInit()) {
Serial.println("OK");
} else {
Serial.println("NO");
}
// initialize OBD-II adapter
do {
mySerial.println("Init...");
} while (!obd.init());
char buf[64];
if (obd.getVIN(buf, sizeof(buf))) {
mySerial.print("VIN:");
mySerial.println(buf);
}
unsigned int codes[6];
byte dtcCount = obd.readDTC(codes, 6);
if (dtcCount == 0) {
mySerial.println("No DTC");
} else {
mySerial.print(dtcCount);
mySerial.print(" DTC:");
for (byte n = 0; n < dtcCount; n++) {
mySerial.print(' ');
mySerial.print(codes[n], HEX);
}
mySerial.println();
}
delay(3000);
}
void loop()
{
readPIDSingle();
readPIDMultiple();
readBatteryVoltage();
if (obd.version > 10) {
readMEMS();
}
}
|
